The influence of truncated-conical implant length on primary stability in maxillary and mandibular regions: an in vitro study using polyurethane blocks.

OBJECTIVES: This in vitro study is aimed at assessing whether implant primary stability is influenced by implant length in artificial bone with varying densities. MATERIALS AND METHODS: A total of 120 truncated-conical implants (60 long-length: 3p L, 3.8 × 14 mm; 60 short-length: 3p S, 3.8 × 8 mm) were inserted into 20, 30, and 40 pounds per cubic foot (PCF) density polyurethane blocks. The insertion torque (IT), removal torque (RT), and resonance frequency analysis (RFA) values were recorded for each experimental condition. RESULTS: In 30 and 40 PCF blocks, 3p S implants exhibited significantly higher IT values (90 and 80 Ncm, respectively) than 3p L (85 and 50 Ncm, respectively). Similarly, RT was significantly higher for 3p S implants in 30 and 40 PCF blocks (57 and 90 Ncm, respectively). However, there were no significant differences in RFA values, except for the 20 PCF block, where 3pS implants showed significantly lower values (63 ISQ) than 3p L implants (67 ISQ) in both the distal and mesial directions. CONCLUSIONS: These results demonstrated that the implant's length mainly influences the IT and RT values in the polyurethane blocks that mimic the mandibular region of the bone, resulting in higher values for the 3p S implants, while the RFA values remained unaffected. However, in the lowest density block simulating the maxillary bone, 3p L implants exhibited significantly higher ISQ values. CLINICAL RELEVANCE: Therefore, our data offer valuable insights into the biomechanical behavior of these implants, which could be clinically beneficial for enhancing surgical planning.

Effects of Implant Diameter on Implant Stability and Osseointegration in the Early Stage in a Dog Model.

Purpose: To determine the optimal implant diameter under limited bone width by comparing the effects of implants with different diameters on implant stability, peri-implant bone stability, and osseointegration. In addition, to evaluate the reliability of resonance frequency analysis (RFA) in detecting osseointegration and marginal bone level (MBL). Materials and Methods: Mandibular premolars and first molars of seven beagle dogs were extracted. After 8 weeks, their mandibular models and radiographic information were collected to fabricate implant templates. Implant sites were randomly divided into three groups according to diameter: Ø3.3, Ø4.1, and Ø4.8 mm. Implant stability quotient (ISQ) measurement and radiographic evaluation were performed after surgery (baseline) and at 4, 8, and 12 weeks. Three dogs were euthanized at 4 weeks to observe osteogenesis and implant-tissue interface biology. Four dogs were euthanized at 12 weeks to observe osseointegration. Hard tissue sections were prepared to analyze osteogenesis (fluorescence double labeling) and osseointegration (methylene blue-acid fuchsin staining). Results: At baseline and at 4, 8, and 12 weeks, the ISQ values of Ø4.1- and Ø4.8-mm implants did not differ (P > .05), but both had higher values than the Ø3.3-mm implants (P < .05). The mean marginal bone resorption (MBR) associated with Ø3.3-, Ø4.1-, and Ø4.8-mm implants was 0.65 ± 0.58 mm, 0.37 ± 0.28 mm, and 0.73 ± 0.37 mm, respectively. The buccal MBR of Ø4.8-mm implants was significantly higher than that of Ø4.1-mm implants (P < .05). The bone-to-implant contact (BIC) percentage at 12 weeks did not differ for any group (P > .05). The correlation coefficients between the ISQ and MBL of the Ø3.3-, Ø4.1-, and Ø4.8-mm implants were -0.84 (P < .01), -0.90 (P < .001), and -0.93 (P < .001), respectively, while that between the ISQ and BIC was 0.15 (P > .05). Conclusions: During the early healing stage, the performance of Ø4.1- and Ø4.8-mm implants in terms of implant stability was better than that of Ø3.3-mm implants. Implant diameter may not influence BIC percentage. RFA can be used to evaluate implant stability and MBL but is not suitable to assess the degree of osseointegration.

Resonance Frequency Analysis to Assess the Stability of Immediate Implants: A Retrospective Clinical Trial.

Adequate implant primary stability is a key factor to obtain osseointegration and can be measured at insertion by insertion torque (IT) and at different timepoints with resonance frequency analysis (RFA), expressed as an implant stability quotient (ISQ). This retrospective study investigated the correlation between ISQ and IT at implant insertion. All patients who were eligible for this single-cohort retrospective clinical trial were treated with an immediate implant. IT parameters were recorded at implant insertion, and ISQ values were recorded at insertion and at 2-, 4-, and 12-month follow-ups. The study comprised 23 patients who received 32 implants. The mean IT value was 46.87 ± 9.66 Ncm (range: 25 to 65 Ncm), and the mean ISQ value at implant insertion was 71.45 ± 4.24 (range: 63 to 78); these values showed a statistically significant correlation (P < .0001). According to the present data and considering the implant design used in this trial, there is a statistically significant and positive correlation between IT and ISQ values. Thus, ISQ can be used as a reliable method to measure implant stability over time.

Insertion Torque and Resonance Frequency Analysis in Tapered and Parallel Dental Implants.

Primary implant stability (PIS) is known to vary with recipient bone mass and density, dental implant design and surgical technique. The objective of this preliminary study was to compare rotational and lateral PIS of same-coronal-diameter conical and parallel implants, using insertion torque recorded with a dental implant motor set and implant stability quotient obtained from resonance frequency analysis (performed with both Osstell and Penguin systems) as measures of rotational and lateral stability, respectively. Additionally, the relationship between PIS and alveolar ridge width (ARW) was explored in both implant types. Sixty dental implants (30 tapered and 30 parallel) were randomly placed with a split-mouth design in 17 patients. Bone density and ARW were estimated from cone beam computed tomography images taken with radiological-surgical templates. Density and width values were similar in the 2 groups (P > .05). Implant coronal diameters were 3.75 mm in all cases, while consistent with the manufacturer's recommendations, final drill bit diameters used were 3.25 and 3.4 mm for parallel and tapered implants, respectively. Insertion torque was higher (P < .05) with parallel implants, but between-group differences in implant stability quotient were not significant (P > .05). In tapered implants, insertion torque was inversely correlated with ARW (P < .001). Notably, significant differences were observed between resonance frequency analysis values from Osstell and Penguin systems (P < .001). In conclusion, future studies should explore how PIS may be influenced by final drill bit size regardless of implant design and potential limits on the effectiveness of tapered implants to achieve good stability in thick low-density bone.

Primary Stability Evaluation of a Novel Tapered Implant Inserted in Low-Density Bone Sites: An In Vitro Study.

Purpose: To evaluate primary stability of a new dental implant design in low-density bone sites, compare it with another implant design previously studied in the same bone density, and explore possible correlations between primary stability parameters. Materials and Methods: The study was carried out on fresh humid bovine bone classified as type III. The test group consisted of 30 DS Prime Taper implants (PT), and the control group consisted of 30 Astra Tech EV implants (EV). All the implants were inserted according to the protocol provided by the manufacturer. After placement, variable torque work (VTW), peak insertion torque (pIT), and resonance frequency analysis (RFA) were recorded. Results: Mann-Whitney test showed that the mean VTW and pIT were significantly higher in the test group PT compared to the control group EV; furthermore, statistical analysis showed that the mean RFA was slightly higher in the control group EV but without reaching statistical significance. Pearson correlation analysis showed a very strong positive correlation between pIT and VTW values in both groups; furthermore, it showed a positive correlation between pIT and RFA values and between VTW and RFA values again in both groups. Conclusion: The results showed that the novel tapered implants were able to reach good primary stability in low-density bone sites and that this was superior to parallel-walled implants when measured with VTW and pIT. Moreover, a statistically significant correlation was found between the three methods used to measure implant primary stability.

Influence of different surgical techniques on primary implant stability in the posterior maxilla: a randomized controlled clinical trial.

BACKGROUND AND OBJECTIVE: Primary stability (PS) is remarkable for secondary stability and implant success. Surgical technique modifications seem to improve primary stability, especially in poor quality bone. The aim of this study was to compare the insertion torque (IT) and implant stability quotients (ISQ) of implants placed with underpreparation, expanders, and standard surgical instrumentation in different bone types. MATERIAL AND METHODS: This randomized controlled clinical trial enrolled 108 patients (n=108 implants) distributed in three study groups: group 1 (n=36) underpreparation technique, group 2 (n=36) expander technique, and group 3 (n=36) conventional drilling. IT was recorded with a torque indicator. ISQ was recorded with resonance frequency analysis immediately after surgery. RESULTS: ISQ values were associated with the patient's bone quality and were higher in bone quality type II (76.65) and type III (73.60) and lower in bone quality type IV (67.34), with statistically significant differences (p<0.0001). Lower stability results were obtained when conventional drilling (69.31) was used compared to the use of underpreparation (74.29) or expanders (73.99) with a level of significance of p=0.008 and p=0.005, respectively. CONCLUSIONS: The surgical technique influences the PS when there is low-quality bone. In low-quality bones, conventional drilling obtains lower ISQ values. CLINICAL RELEVANCE: Replace the conventional drilling technique for an alternative, underpreparation or expanders, in low-quality bone in order to achieve greater primary stability.

Influence of Multiple Sterilization on Performance of Titanium Pegs When Measuring Implant Stability With Resonance Frequency Analyses.

This in vitro study was conducted to investigate the repeatability of the implant stability quotients (ISQ) measured with multipegs after numerous sterilizations and to detect the exact time when the readings start to deviate. Multipegs were sterilized with 3 different methods (autoclaved, autoclaved + ultrasonic cleaner, chemical disinfection + autoclaved) and grouped according to the method applied. All specimens were put into the autoclave with sealed packages every time they were sterilized. Each specimen was sterilized 50 times according to the technique described in its group after an ISQ measurement was performed. Results of the 2-way analysis of variance showed that neither the sterilization method nor the cycles, nor their interaction, were statistically significant. A multipeg may be reused multiple times after sterilization procedures and may be more cost-effective than a disposable smartpeg for checking implant stability after confirming these results in further investigations.

The Effects of Injectable Platelet-Rich Fibrin on Implant Stability.

PURPOSE: To investigate the effects of injectable platelet-rich fibrin (i-PRF) on implant stability. MATERIALS AND METHODS: A total of 40 implants (BEGO Semados RS/RSX implants, BEGO Implant System) were surgically placed in 15 patients between the ages of 25 and 67 years who had mandibular edentulous areas. After the implant sockets were prepared with the appropriate protocol, i-PRF was applied to the implant surface and socket with the help of a 5-cc sterile syringe in the study group, and implants were placed without i-PRF in the control group. In the research process, the resonance frequency analysis (RFA) method was used to measure implant stability. The implant stability quotient (ISQ) values were determined during the time of the operation and at the first, second, and fourth weeks. RESULTS: The results obtained after the stability measurement periods showed that the decrease in the mean ISQ values in the control group was statistically significant in the first week. Evaluations made in the following weeks were not statistically significant. The study group showed an increase in ISQ values during the measurement periods, and the increases in the second and fourth weeks were statistically significant. CONCLUSION: I-PRF had positive effects on early implant stability, and i-PRF can be safely used in dental implant surgery and promotes bone healing around dental implants.

Resonance Frequency Analysis to Evaluate the Effect of Different Drilling Techniques on Implant Stability at Different Time Intervals: A Randomized Clinical Trial.

PURPOSE: To evaluate the effect of different drilling techniques on implant stability at different time intervals. MATERIALS AND METHODS: Patients were randomly allotted into three groups based on drilling technique for osteotomy: conventional drilling technique; simplified drilling technique; or modified conventional drilling technique. In 30 patients (n = 10 each group), a total of 44 implants were placed. In the conventional drilling technique, drills with increasing diameters were used. In the simplified drilling technique, only pilot and final-diameter drills were used. In the modified conventional drilling technique, all the drills were used in sequential order in the clockwise direction except the last drill, which was used in the counterclockwise direction. Implant stability quotient was recorded immediately after placing implants and at 1 and 3 months. Statistical analysis was performed with two-way analysis of variance (ANOVA) and Student t test. RESULTS: Two-way ANOVA showed that drilling technique (P < .001) and time (P = .002) did have a statistically significant effect on implant stability quotient. The modified conventional drilling technique showed a drop in secondary implant stability at 1 month that was negligible compared to the other techniques. After 1 month, there was a significant increase in implant stability quotient with the modified conventional drilling technique compared to the conventional drilling technique (P = .001). The least crestal bone loss during 3 months of follow-up was with the modified conventional drilling technique (0.37 ± 0.06). CONCLUSION: Secondary stability increased with the modified conventional drilling technique in 3 months and showed a negligible drop at 1 month. This novel drilling technique had an early shift from a decrease to an increase in stability pattern, along with the least crestal bone loss at 3 months.

Primary Stability of Trabecular Metal Implant in Comparison to Fully Threaded Implants: In Vitro Study Simulating Immediate Implant Placement.

The aim of this study was to evaluate primary stability of 3.7-mm diameter porous tantalum Trabecular Metal (TM) implant, and compare it to fully threaded implants, in the in vitro model of immediate implant placement in the anterior maxilla. A total of 60 implants were placed into bovine ribs using surgical guides. Implants were divided in 3 groups of 20 according to the design: TM, Tapered Screw-Vent (TSV), and NobelReplace. To simulate immediate placement in anterior maxilla, implants were placed under a sharp angle toward the ribs, not fully submerged. Placement angle of 20.7° was calculated after analysis of 148 virtually planned implants on cone beam computerized tomography scans of 40 patients. No statistically significant difference in implant stability quotient (ISQ) was found between TM (65.8 ± 2.6), TSV (64.7 ± 2.7), and NobelReplace (64.6 ± 2.7). TSV implants achieved higher insertion torque (37.0 ± 4.8 Ncm) than TM (32.9 ± 5.2 Ncm) and NobelReplace (23.2 ± 3.3 Ncm). TSV had the shortest insertion time of 13.5 ± 1.0 seconds, compared to 15.2 ± 1.2 seconds for TM, and 19.7 ± 1.7 seconds for NobelReplace. Pearson correlation analysis showed significantly correlated insertion torque and ISQ values for TM group (P = .011, r = .56), a nonsignificant correlation was found for TSV and NobelReplace. The results of the present study indicate that TM implant can achieve good primary implant stability in insertion torque and resonance frequency analysis.

Intra- and inter-operator concordance of the resonance frequency analysis. A cross-sectional and prospective clinical study.

OBJECTIVE: Resonance frequency analysis (RFA) provides an evaluation of implant stability over time. This analysis is a non-invasive, precise, and objective method. Several studies compare the RFA system with other devices. However, few investigations analyze repeatability and reproducibility between different operators. The aim of this study was to evaluate the intra- and inter-operator concordance of the Osstell® ISQ. MATERIAL AND METHODS: RFA measurements were performed with Osstell® ISQ in a total of 37 implants placed in 21 patients. At the time of implant placement, 6 measurements per implant were taken by three different experienced operators. Three measurements were carried out consecutively and three by removing and placing the SmartPeg-Osstell® to assess intra-operator and inter-operator agreement. RESULTS: Intra-operator concordance according to the intraclass correlation coefficient (ICC) showed high concordance. The ICC values were higher than 0.9 (p < 0.0001) for consecutive measures and alternative measures, being almost perfect of Landis & Koch classification. For inter-operator concordance The ICC was 0.709 (p < 0.0001) and 0.670 (p < 0.0001) for consecutive and alternative measures, respectively, both estimates being in the substantial category. In torque and ISQ values, no statistically significant differences were observed when operators and measurements were compared. CONCLUSIONS: Osstell® ISQ system was stable both in intra-operator and inter-operator measurements. This device has excellent repeatability and reproducibility, demonstrating reliability to measure the stability of dental implants. CLINICAL RELEVANCE: Resonance frequency analysis (RFA) is a non-invasive, objective, and reliable diagnostic method to determine the ideal moment to load the implant, as well as to predict possible failures.

Is Resonance Frequency Analysis a Reliable Evaluation for Primary Stability of Implants Without Apical Contact?

PURPOSE: The primary stability of dental implants is one of the most crucial factors for providing long-term success of osseointegration. Vertical deficiencies, such as those due to maxillary sinus pneumatization, may cause a severe vertical limitation to residual bone height. This study aimed to examine the primary stabilization of implants without apical contacts. MATERIALS AND METHODS: Eighty bone-level implants (4.1-mm diameter/10-mm length) were placed into polyurethane test blocks without apical contacts. According to coronal bone-to-implant contact, groups were set as 4, 6, 8, and 10 mm, respectively. Resonance frequency analysis (RFA) using a SmartPeg was performed separately toward the transversal and horizontal axes by two independent researchers. Data were statistically compared for interobserver and among groups. RESULTS: Interobserver reliability varied from moderate to excellent (intraclass correlation coefficient [ICC]: 0.629 to 0.985). There were no significant differences among the 6 mm, 8 mm, and 10 mm groups, although the 4 mm group showed the significantly lowest stability (P < .001). Transversal and longitudinal measurements of the same groups did not show a parallel correlation statistically. CONCLUSION: RFA values may be affected by the finger torque in tightening of the SmartPeg among different researchers. Fully placed implants did not significantly show the highest stability among various apically contactless groups. Consequently, RFA should not be used alone to evaluate primary stability for implants without an apical contact.

The influence of implant design on implant stability in low-density bone under guided surgical template in inexperienced surgeons: A pilot randomized controlled clinical trial using resonance frequency analysis.

INTRODUCTION: There are several factors that greatly influence implant stability with implant design being a paramount factor; however, few studies investigate its impact. AIM: To investigate the implant stability in relation to two different implant designs, a cylindrical shaped single-threaded design (CS/ST) and a tapered shaped double-threaded design (TS/DT) using resonance frequency analysis over the first 8 weeks after implantation. MATERIALS AND METHODS: Twenty-eight implants were randomly allocated using computer-generated random numbers into two groups and were placed as single tooth implant in the posterior arch in human jaw as specimens. iCAT™ CBCT scan (Hatfield, PA) was used to determine the bone density according to Misch's Bone classification. The osseotomy sites were prepared and implants were placed with guided surgical template by inexperienced surgeons which were prepared with the same implant planning software (3shape® implant studio). The implant stability was measured using the resonance frequency analysis Osstell® ISQ (Osstell AB, Sweden) on the implant level over the first 8 weeks at three different time intervals. A mean implant stability quotient (ISQ) value was recorded at each measurement time points. The first ISQ of each implant recorded at the time of implant placement were considered as baseline and were the so-called primary stability. RESULTS: All 28 dental implants were analyzed. A similar pattern of implant stability changes was observed in both implant designs. A significant decreased was found at the first 4 weeks after implantation (p < 0.05) before ascending to maximum cumulative stability by the eighth week (p < 0.05). Between the two groups, TS/DT group had a higher mean ISQ values than that of the CS/ST group at all three observation periods but did not reach statistical significance (p = 0.69). Regarding different types of bone, TS/DT showed a significant difference in mean ISQ values in D4 bone. To date, all 28 implants are in function with no failure/and or complications. CONCLUSIONS: The difference in implant design did not significantly influence the implant stability. TS/DT shows superiority over CS/ST when placed in D4 bone and offer a significant advantage due to their positive bounce back of the ISQ values by the eighth week after implant installation. CLINICAL TRIAL REGISTRATION: TCTR20211020005.

Peri-implant bone microstructural analysis and comparison of resonance frequency analysis before prosthetic placement: a retrospective study.

OBJECTIVES: Fractal analysis is a mathematical method used for the calculation of bone trabeculation and lacunarity. This study aims to evaluate the relationship between resonance frequency analysis (RFA) and fractal dimension (FD) of peri-implant bone to determine the preload stability of implants. MATERIALS AND METHODS: In this study, the results of the fractal analysis calculated from the resonance frequency analysis results taken in the 3rd month of the patients who underwent 2-stage implant by the same doctor and the radiographs taken in the same session were evaluated. A hundred implants in 20 patients were applied in this study. The implant stability quotient (ISQ) values of the implants and fractal dimension values of the peri-implant bone were calculated. RESULTS: The findings showed that the ISQ1 (p = 0.008), ISQ2 (p = 0.038), ROI2 (p = 0.013), and ROI3 (p < 0.001) values were statistically significantly higher in men than women. The ISQ1 (p = 0.003), ISQ2 (p = 0.013), ROI1 (p = 0.011), and ROI3 (p < 0.001) of the mandible were statistically higher than the maxilla. The fractal dimension cut-off value to assess prosthetic loading was found 1.198. CONCLUSION: Fractal analysis is a non-invasive method that can be used in conjunction with clinical examination in the prosthetic loading decision of implants. It is a valuable parameter that can be used without the need for an extra device when it is necessary to reduce the clinical study time. CLINICAL RELEVANCE: Calculating the fractal dimension of the peri-implant bone is a practical, economical, and applicable method for clinicians. FD calculated from panoramic radiographs used for diagnosis in routine treatments in clinics where access to the necessary devices for ISQ measurement is not available will contribute to clinical practice.

A comparative evaluation of the effect of platelet rich fibrin matrix with and without peripheral blood mesenchymal stem cells on dental implant stability: A randomized controlled clinical trial.

Technological advances in the field of implantology have led to the concept of surface modifications to enhance implant stability by utilization of current concepts of tissue engineering and materials such as platelet concentrates and stem cells. The purpose of the present randomized controlled clinical trial was to evaluate and compare the effect of platelet rich fibrin matrix (PRFM) with and without peripheral blood mesenchymal stem cells (PBMSCs) on implant stability; by assessing the bone to implant contact (BIC) using resonance frequency analysis (RFA), insertion torque and also to establish and correlate the same with implant stability quotient (ISQ). A total of 15 patients with 30 sites ensuring a minimum of two dental implants adjacently placed in an edentulous area; with the age group of 25-50 years of both the sexes were categorized into Group 1 (dental implant with PRFM) and Group 2 (dental implant with PBMSCs embedded in PRFM). Insertion torque values at the time of dental implant placement and ISQ using RFA was recorded at 1 week, 1 month, and 3 months post operatively. There was no significant difference (p = 0.81) in Insertion torque values between both the groups (G1 and G2). Platelet rich fibrin matrix along with PBMSCs enhanced implant stability as higher and statistically significant ISQ values were noted at 1 week (p = 0.18), 1 month (p ≤ 0.001), and 3 months (p ≤ 0.001) intervals in the G2 group. Platelet rich fibrin matrix and PBMSCs showed promising results as a potential regenerative material for increasing and enhancing BIC and hence implant stability.

Clinical Evaluation of a Novel Laser-Ablated Titanium Implant System for Bone Anchored Hearing Systems in a Pediatric Population and the Relationship of Resonance Frequency Analysis With Implant Survival.

OBJECTIVE: To evaluate the clinical outcomes of pediatric patients implanted a novel 4.5 mm wide laser ablated titanium bone anchored implant system and to evaluate the implant stability over the first 12-month period. STUDY DESIGN: A prospective, single-subject, repeated measure, cohort study. Participants served as their own controls. SETTING: Community and tertiary referral hospital pediatric assessment center. PATIENTS: A total of 115 consecutive pediatric patients aged 4 to 15 years were implanted with 176 laser ablated titanium bone anchored implants from January 2016 to January 2019. MAIN OUTCOME MEASURE: Clinical outcomes, implant failure rates, and post implantation implant stability quotient (ISQ) scores were studied over the first 12-month period. Data were analyzed for statistical significance through mixed effect modeling, with the significance level p = 0.01. RESULTS: A median 12-month survival of 96.6% was observed. Six implants (3.5%) were lost in total, one of these (0.6%) was lost due to trauma. Adverse skin reactions (Holgers grade 2-4) were observed in 4.4% of all postoperative visits, occurring in 22 individuals (19.1%). Neither the ISQ high (ISQH) nor ISQ low (ISQL) values increased significantly between the stage 1 and 2 surgeries. In contrast, the ISQ results, irrespective of abutment size, demonstrated an increasing trend from 49.1 to 57 over the 12 months review period. A statistically significant change was only demonstrated from the 3 months follow up onwards. CONCLUSION: The use of 4.5 mm wide laser-ablated titanium bone anchored hearing implants resulted in superior survival rates and excellent clinical outcomes compared with previous implant systems.

Comparison of Reliability of 3 Resonance Frequency Analysis Devices: An In Vitro Study.

The purpose of the present study was to investigate the intraobserver and interobserver reliability of 3 resonance frequency analysis (RFA) devices and to compare the implant stability quotient (ISQ) values according to implant macro design and diameter in 2 different bone densities. A total of 64 implants (Neoss ProActive; Neoss; Harrogate, UK) of varying diameters (3.5 and 4.0 mm) and implant macro design (tapered and straight) were placed in 2 artificial bone blocks (the density of type 2 and 3). The implant primary stability was measured using Osstell IDx (Osstell; Göteborg, Sweden), Osstell Beacon and Penguin RFA (Integration Diagnostics; Göteborg, Sweden). The ISQ value of each implant was measured by 2 observers and recorded 5 times in 2 directions. The intraobserver and interobserver reliability of RFA devices were evaluated. In addition to that, mean ISQ values were calculated for each RFA device to evaluate the effect of implant diameter, implant macro design, and bone density on ISQ values. ISQ values were significantly higher for implants placed within the type 2 bone than for the type 3 bone. The 4.0-mm diameter implants presented higher ISQ values than 3.5-mm diameter implants. The intraclass correlation coefficient (ICC) values for intraobserver reliability were above 0.85 for each observer and the ICC values for interobserver reliability were 0.94, 0.93, and 0.98 for Osstell IDx, Osstell Beacon, and Penguin RFA, respectively. Although there was excellent interobserver reliability with 3 RFA devices, the intraobserver reliability of Osstell Beacon and Penguin RFA were slightly better than Osstell IDx. Bone density and implant diameter were parameters affecting the primary stability of implants.

Comparison of the Stability of Sandblasted, Large-Grit, and Acid-Etched Treated Mini-Screws With Two Different Surface Roughness Values: A Histomorphometric Study.

PURPOSE: To evaluate the effects of 2 different surface roughness values produced by sandblasted, large-grit, and acid-etched treatments at different loading conditions on the stability of mini-screws. MATERIAL AND METHODS: A total of 56 mini-screws (Group 1; 28 with Ra value of 1 µm, Group 2; 28 with Ra value of 1.5 µm) were inserted into the tibia of fourteen New Zealand rabbits. Surface analysis was performed before the placement of the miniscrews using multi-technique characterization. The mini-screws were loaded with 500 grf after different healing times: unloaded, immediate, 4 and 8 weeks. Resonance frequency analyses were performed immediately after mini-screw placement and at the end of loading. Biomechanical and histomorphometric analyses were also performed at the end of the loading period. RESULTS: All mini-screws preserved their stability at the end of the loading period. However, the resonance frequency analyses showed higher implant stability quotient scores for 8-week group, unlike the immediate loading and unloaded groups (P < 0.05). According to the infinite focus microscopy results, prolongation of healing time resulted in a greater bone area on the loaded mini-screws in Group 2 (P < 0.05). Similarly, the histomorphometric analysis revealed higher bone-to-implant contact values in the 8-week group. There was no significant difference in the stability between the miniscrews with the Ra values of 1 and 1.5 µm. CONCLUSIONS: Sandblasted, large-grit, and acid-etched treated mini-screws showed significantly higher stability with healing time under heavy forces. Sandblasted, large-grit, and acid-etched treated mini-screws can be removed without fracture of the screw or the bone surfaces.

Comparação da expansão óssea promovida pela técnica de osseodensificação com dois tipos de conjunto de fresas / Comparison of bone expansion promoted by the osseodensification technique with two types of drill sets

Introdução: A estabilidade primária é um importante indicador de sucesso da osseointegração. Porém, fatores locais com osso de baixa intensidade podem interferir negativamente na obtenção da estabilidade primária. Objetivo: O presente estudo avaliou o efeito de diferentes direções, velocidades de rotação e sistemas de fresagem na expansão de perfurações e estabilidade de implantes instalados em blocos mimetizando osso do tipo IV. Material e método: Foram instalados 50 implantes em blocos de poliuretano sólido rígido. Esses implantes foram igualmente divididos em cinco grupos (n = 10): 1) Fresa Maximus (utilizadas no sentido horário a 1200rpm); 2) Fresa Maximus (utilizadas no sentido horário a 600rpm); 3) Fresa Neodent (utilizadas no sentido horário a 800rpm); 4) Fresa Neodent (utilizadas no sentido anti-horário a 800rpm); 5) Fresa Neodent (utilizadas no sentido anti-horário a 600rpm). Foram executadas análises de estabilidade dos implantes através de testes de torque de inserção e remoção, além das análises de frequência de ressonância. Adicionalmente, a expansão associada às perfurações promovida pelas brocas foi avaliada por meio de análises tomográficas. Resultado: Verificou-se que os implantes instalados após o preparo da perfuração com as brocas Maximus a 600rpm apresentaram valores de torque de inserção maiores, quando comparados ao grupo de implantes instalados em perfurações confeccionadas com brocas Neodent. Ademais, as brocas Maximus apresentaram valores de expansão maiores que as brocas Neodent. Conclusão: As brocas Maximus são mais eficientes em promover a osseodensificação, e sua utilização está associada ao aumento da estabilidade dos implantes instalados em blocos mimetizando osso do tipo IV.

Introduction: Primary stability is an important indicator to obtain a successful osseointegration. However, local factors like bone with low density can negatively interfere in obtaining primary stability. Objective: This study assessed the effect of different drilling systems, speeds, and movement directions on the expansion of perforations and the stability of implants placed in blocks that mimicked type IV bone. Material and method: Fifty implants were installed in rigid solid polyurethane blocks and equally divided into the following five groups (n = 10): 1) Maximus Driller (on a clockwise direction at 1200rpm); 2) Maximus Driller (on a clockwise direction at 600rpm); 3) Neodent Driller (on a clockwise direction at 800rpm); 4) Neodent Driller (on a counter clockwise direction at 800rpm); 5) Neodent Driller (on a counter clockwise direction at 600rpm). The stability analyses of the implants were performed through insertion and removal torque testing, in addition to resonance frequency analysis. Additionally, the expansion promoted by the drills associated with the perforations was assessed through tomographic analysis. Result: We found that implants placed after drilling preparation with Maximus drills at 600 rpm had higher values of insertion torque than the group of implants installed in drillings made with Neodent drills. In addition, the maximus drills showed higher expansion values than the Neodent drills. Conclusion Maximus drills are more efficient in promoting osseodensification and their use was associated with increased stability of implants installed in blocks that mimicked type IV bone.

Clinical evaluation and resonance frequency analysis of laser-ablated titanium bone-anchored hearing implant system in children with Down Syndrome.

OBJECTIVES: To evaluate complication rates and resonance frequency analysis (RFA) of the stability of a new laser-ablated titanium Bone Anchored hearing Implant system in children with Down syndrome. METHODS: A prospective, single-subject, repeat measure, cohort study in which each participant served as their own control. Consecutive paediatric patients 4yrs- 15 years old, with a primary diagnosis of Down syndrome (trisomy 21) were implanted between January 2015-January 2020 with BHX Oticon wide implants. Evaluation of soft tissue reactions, fixture failure rates and post implantation Implant stability Quotient (ISQ) at both fixtures and abutment levels were studied over a 12-month period. Data was analysed for statistical significance through mixed effect modelling with significance set at p = 0.01. RESULTS: 31 consecutive paediatric patients with a diagnosis of Down syndrome were implanted with 43 Ponto BHX Oticon™ implant system. Twelve children had bilateral implants and nineteen were unilateral. Over the 12 month follow up 2 fixtures (4.6%) were lost, and adverse skin reactions (Holgers >2) were recorded in 3.2% of all clinical reviews. Implant level stability quotient showed no statically significant change between first and second stage 71.1-71.7. Abutment level ISQ increased from 46.2 to 56.7 p = 0.0001 at the 12-month review point as compared to that recorded at loading. CONCLUSION: Implant survival and adverse skin reactions were found to be in keeping with those in published literature and much improved compared to previous implant systems placed at this centre. Although abutment level ISQ showed an increase over the review period no correlation between this and implant loss can be concluded.